Aug 11, 2016  Windows 10 Anniversary Update, the major feature update for Windows 10, comes with a feature called TCP/IP Receive Window Auto-Tuning which is enabled by default. This feature is intended to improve performance of apps which receive TCP packets over a network. Under certain conditions, this feature can reduce your Internet speed. Oct 05, 2018  Disable auto tuning Windows 10 Can i disable auto tuning windows 10? This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread. Netsh int tcp set global autotuninglevel=disabled When that completes, close Command Prompt. However, the TCP auto tuning feature may get things wrong sometimes. Instead of optimal true receive window size, incompatible and out of range RWIN size may be used. By default, Windows in normal auto tuning level will use RWIN size of 256 bytes with a scale factor of 8. The Receive Window Auto-Tuning feature lets the operating system continually monitor routing conditions such as bandwidth, network delay, and application delay. Therefore, the operating system can configure connections by scaling the TCP receive window to maximize the network performance. Disabling auto tuning of TCP Windows Size should not cause any negative effects, only that TCP Window Size will always at default value without ability to optimization to each connection. Anyway, if there is any side effect after turn off auto tuning, simply re-enable back it. Check the State or Current Setting of TCP Receive Window Auto-Tuning.

1. Tcp Windows Auto Tuning
2. Auto Tuning Windows 10
3. Sql Tuning Tcp Window
4. Windows 10 Tcp Tuning Utility
5. Tcp Auto Tuning

-->

Applies To: Windows Server 2012

This topic contains the following sections.

Determining the correct tuning settings for your network adapter depend on the following variables:

• The network adapter and its feature set

• The type of workload performed by the server

• The server hardware and software resources

• Your performance goals for the server

If your network adapter provides tuning options, you can optimize network throughput and resource usage to achieve optimum throughput based on the parameters described above.

The following sections describe some of your performance tuning options.

Enabling Offload Features

Turning on network adapter offload features is usually beneficial. Sometimes, however, the network adapter is not powerful enough to handle the offload capabilities with high throughput. For example, enabling segmentation offload can reduce the maximum sustainable throughput on some network adapters because of limited hardware resources. However, if the reduced throughput is not expected to be a limitation, you should enable offload capabilities, even for this type of network adapter.

Note

Some network adapters require offload features to be independently enabled for send and receive paths.

Enabling Receive Side Scaling (RSS) for Web Servers

RSS can improve web scalability and performance when there are fewer network adapters than logical processors on the server. Install windows 10 on mac without boot camp assistant. When all the web traffic is going through the RSS-capable network adapters, incoming web requests from different connections can be simultaneously processed across different CPUs.

It is important to note that due to the logic in RSS and Hypertext Transfer Protocol (HTTP) for load distribution, performance might be severely degraded if a non-RSS-capable network adapter accepts web traffic on a server that has one or more RSS-capable network adapters. In this circumstance, you should use RSS-capable network adapters or disable RSS on the network adapter properties Advanced Properties tab. To determine whether a network adapter is RSS-capable, you can view the RSS information on the network adapter properties Advanced Properties tab.

RSS Profiles and RSS Queues

RSS predefined profiles are new in Windows Server 2012.

The default profile is NUMA Static, which changes the default behavior from previous versions of the operating system. To get started with RSS Profiles, you can review the available profiles to understand when they are beneficial and how they apply to your network environment and hardware.

For example, if you open Task Manager and review the logical processors on your server, and they seem to be underutilized for receive traffic, you can try increasing the number of RSS queues from the default of 2 to the maximum that is supported by your network adapter. Your network adapter might have options to change the number of RSS queues as part of the driver.

Increasing Network Adapter Resources

For network adapters that allow manual configuration of resources, such as receive and send buffers, you should increase the allocated resources. Some network adapters set their receive buffers low to conserve allocated memory from the host. The low value results in dropped packets and decreased performance. Therefore, for receive-intensive scenarios, we recommend that you increase the receive buffer value to the maximum.

Note

If a network adapter does not expose manual resource configuration, it either dynamically configures the resources, or the resources are set to a fixed value that cannot be changed.

Enabling Interrupt Moderation

To control interrupt moderation, some network adapters expose different interrupt moderation levels, buffer coalescing parameters (sometimes separately for send and receive buffers), or both.

You should consider interrupt moderation for CPU-bound workloads, and consider the trade-off between the host CPU savings and latency versus the increased host CPU savings because of more interrupts and less latency. If the network adapter does not perform interrupt moderation, but it does expose buffer coalescing, increasing the number of coalesced buffers allows more buffers per send or receive, which improves performance.

Performance Tuning for Low Latency Packet Processing

Many network adapters provide options to optimize operating system-induced latency. Latency is the elapsed time between the network driver processing an incoming packet and the network driver sending the packet back. This time is usually measured in microseconds. For comparison, the transmission time for packet transmissions over long distances is usually measured in milliseconds (an order of magnitude larger). This tuning will not reduce the time a packet spends in transit.

Following are some performance tuning suggestions for microsecond-sensitive networks.

• Set the computer BIOS to High Performance, with C-states disabled. However, note that this is system and BIOS dependent, and some systems will provide higher performance if the operating system controls power management. You can check and adjust your power management settings from Control Panel or by using the powercfg command. For more information, see Powercfg Command-Line Options

• Set the operating system power management profile to High Performance System. Note that this will not work properly if the system BIOS has been set to disable operating system control of power management.

• Enable Static Offloads, for example, UDP Checksums, TCP Checksums, and Send Large Offload (LSO).

• Enable RSS if the traffic is multi-streamed, such as high-volume multicast receive.

• Disable the Interrupt Moderation setting for network card drivers that require the lowest possible latency. Remember, this can use more CPU time and it represents a tradeoff.

• Handle network adapter interrupts and DPCs on a core processor that shares CPU cache with the core that is being used by the program (user thread) that is handling the packet. CPU affinity tuning can be used to direct a process to certain logical processors in conjunction with RSS configuration to accomplish this. Using the same core for the interrupt, DPC, and user mode thread exhibits worse performance as load increases because the ISR, DPC, and thread contend for the use of the core.

System Management Interrupts

Many hardware systems use System Management Interrupts (SMI) for a variety of maintenance functions, including reporting of error correction code (ECC) memory errors, legacy USB compatibility, fan control, and BIOS controlled power management. The SMI is the highest priority interrupt on the system and places the CPU in a management mode, which preempts all other activity while it runs an interrupt service routine, typically contained in BIOS.

Unfortunately, this can result in latency spikes of 100 microseconds or more. If you need to achieve the lowest latency, you should request a BIOS version from your hardware provider that reduces SMIs to the lowest degree possible. These are frequently referred to as “low latency BIOS” or “SMI free BIOS.” In some cases, it is not possible for a hardware platform to eliminate SMI activity altogether because it is used to control essential functions (for example, cooling fans).

Note

The operating system can exert no control over SMIs because the logical processor is running in a special maintenance mode, which prevents operating system intervention.

Performance Tuning TCP

You can performance tune TCP using the following items.

Details are provided in the following sections.

TCP Receive Window Auto-Tuning

Prior to Windows Server 2008, the network stack used a fixed-size receive-side window that limited the overall potential throughput for connections. One of the most significant changes to the TCP stack is TCP receive window auto-tuning. You can calculate the total throughput of a single connection when you use this fixed size default as:

Total achievable throughput in bytes = TCP window * (1 / connection latency)

Tcp Windows Auto Tuning

For example, the total achievable throughput is only 51 Mbps on a 1 GB connection with 10 ms latency – which is a reasonable value for a large corporate network infrastructure.

With auto-tuning, however, the receive-side window is adjustable, and it can grow to meet the demands of the sender. It is entirely possible for a connection to achieve the full line rate of a 1 GB connection. Network usage scenarios that might have been limited in the past by the total achievable throughput of TCP connections can now fully use the network.

Windows Filtering Platform

Auto Tuning Windows 10

The Windows Filtering Platform (WFP) that was introduced in Windows Vista and Windows Server 2008 provides APIs to non-Microsoft independent software vendors (ISVs) to create packet processing filters. Examples include firewall and antivirus software.

Sql Tuning Tcp Window

Note

Windows 10 Tcp Tuning Utility

A poorly written WFP filter can significantly decrease a server’s networking performance.

Tcp Auto Tuning

For more information, see Windows Filtering Platform in the Windows Dev Center.

TCP Parameters

The following registry keywords from Windows Server 2003 are no longer supported, and they are ignored in Windows Server 2012, Windows Server 2008 R2, and Windows Server 2008.

• TcpWindowSize

• NumTcbTablePartitions

• MaxHashTableSize